Moin moin Ingo!

:) Danke für Dein Reply!
(Bekommt man eigentlich keine Mail, wenn jemand auf ein Posting
antwortert? Muss/Kann ich das irgendwo anknipsen?)

Also…..

Distro: Eigenbau auf LFS basierend, i386 (Athlon 2400+), Mutterbrett 8k5A3+ (VIA KT133), PS2-Schlüsselbrett, Kernel preemptiv, IOAPIC aktiviert.

Nach ein bischen weiterer Forschung und Umstieg auf Linux-2.6.14-2 ergibt sich
folgendes Bild:
a.) Die Tastatur ist nicht das Problem. Ihr Erkennung ist nur die letzte
Meldung auf dem Monitor… :)
b.) Wartet man lange genug, bootet der Kernel durch und danach treten keine
weiteren Fehler auf.
c.) Der “Hänger” (die “Warteschleife”) wird von dem USB-Geraffel erzeugt.
d.) lspci -v | grep HCI liefert bei mir:

00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])

e.) Bleibt der Boot hängen, hilft häufiges ein- und austecken irgendeines
USB-Gerätes.
f.) Die Macke gab es bei der 2.6.13er-Serie bei gleicher Hartware nicht.
g.)
dmesg liefert:
Linux version 2.6.14.1 (root@solfire) (gcc version 4.0.2) #2 PREEMPT Thu Nov 10 19:04:05 CET 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 – 000000000009e800 (usable)
BIOS-e820: 000000000009e800 – 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 – 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 – 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 – 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 – 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 – 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 – 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 – 0000000100000000 (reserved)
511MB LOWMEM available.
found SMP MP-table at 000f5e30
On node 0 totalpages: 131056
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126960 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 VIA694 ) @ 0x000f7840
ACPI: RSDT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
ACPI: FADT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
ACPI: MADT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff7200
ACPI: DSDT (v001 VIA694 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Built 1 zonelists
Kernel command line: floppy=daring rootfstype=reiserfs root=/dev/hda3 ro vga=ext autotune hda=autontune db=autotune hdc=autotune hdd=autotune idex=dma
ide_setup: hda=autontune — BAD OPTION
ide_setup: hdc=autotune — OBSOLETE OPTION, WILL BE REMOVED SOON!
ide_setup: hdd=autotune — OBSOLETE OPTION, WILL BE REMOVED SOON!
ide_setup: idex=dma — BAD OPTION
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1988.640 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80×50
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 514052k/524224k available (3295k kernel code, 9620k reserved, 923k data, 176k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode… Ok.
Calibrating delay using timer specific routine.. 3981.85 BogoMIPS (lpj=7963709)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: AMD Athlon(tm) XP 2400+ stepping 01
Enabling fast FPU save and restore… done.
Enabling unmasked SIMD FPU exception support… done.
Checking ‘hlt’ instruction… OK.
tbxface-0109 [02] load_tables : ACPI Tables successfully acquired
Parsing all Control Methods:…………………………………………………………………………………………………………………………….
Table [DSDT](id 0005) – 520 Objects with 47 Devices 142 Methods 31 Regions
ACPI Namespace successfully loaded at root c0583398
evxfevnt-0091 [03] enable : Transition to ACPI mode successful
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
softlockup thread 0 started up.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb3d0, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
evgpeblk-0988 [06] ev_create_gpe_block : GPE 00 to 0F [_GPE] 2 regs on int 0x9
evgpeblk-0996 [06] ev_create_gpe_block : Found 6 Wake, Enabled 1 Runtime GPEs in this block
Completing Region/Field/Buffer/Package initialization:………………………………………………………………..
Initialized 31/31 Regions 13/13 Fields 20/20 Buffers 10/19 Packages (529 nodes)
Executing all Device _STA and_INI methods:……………………………………………
51 Devices found containing: 51 _STA, 2 _INI methods
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI: Scanning bus 0000:00
PCI: Found 0000:00:00.0 [1106/3099] 000600 00
PCI: Calling quirk c0277f60 for 0000:00:00.0
PCI: Calling quirk c0278510 for 0000:00:00.0
PCI: Calling quirk c03d6600 for 0000:00:00.0
PCI: Calling quirk c03d66d0 for 0000:00:00.0
PCI: Calling quirk c03d6a10 for 0000:00:00.0
PCI: Found 0000:00:01.0 [1106/b099] 000604 01
PCI: Calling quirk c0277f60 for 0000:00:01.0
PCI: Calling quirk c0278510 for 0000:00:01.0
PCI: Calling quirk c03d6600 for 0000:00:01.0
PCI: Calling quirk c03d6a10 for 0000:00:01.0
PCI: Found 0000:00:08.0 [109e/036e] 000400 00
PCI: Calling quirk c0277f60 for 0000:00:08.0
PCI: Calling quirk c0278510 for 0000:00:08.0
PCI: Calling quirk c03d6600 for 0000:00:08.0
PCI: Calling quirk c03d6a10 for 0000:00:08.0
PCI: Found 0000:00:08.1 [109e/0878] 000480 00
PCI: Calling quirk c0277f60 for 0000:00:08.1
PCI: Calling quirk c0278510 for 0000:00:08.1
PCI: Calling quirk c03d6600 for 0000:00:08.1
PCI: Calling quirk c03d6a10 for 0000:00:08.1
PCI: Found 0000:00:09.0 [105a/4d68] 000180 00
PCI: Calling quirk c0277f60 for 0000:00:09.0
PCI: Calling quirk c0278510 for 0000:00:09.0
PCI: Calling quirk c03d6600 for 0000:00:09.0
PCI: Calling quirk c03d6a10 for 0000:00:09.0
PCI: Found 0000:00:0b.0 [1105/8300] 000480 00
PCI: Calling quirk c0277f60 for 0000:00:0b.0
PCI: Calling quirk c0278510 for 0000:00:0b.0
PCI: Calling quirk c03d6600 for 0000:00:0b.0
PCI: Calling quirk c03d6a10 for 0000:00:0b.0
PCI: Found 0000:00:0d.0 [1000/000f] 000100 00
PCI: Calling quirk c0277f60 for 0000:00:0d.0
PCI: Calling quirk c0278510 for 0000:00:0d.0
PCI: Calling quirk c03d6600 for 0000:00:0d.0
PCI: Calling quirk c03d6a10 for 0000:00:0d.0
PCI: Found 0000:00:10.0 [1106/3038] 000c03 00
PCI: Calling quirk c0277f60 for 0000:00:10.0
PCI: Calling quirk c0278510 for 0000:00:10.0
PCI: Calling quirk c03d6600 for 0000:00:10.0
PCI: Calling quirk c03d6a10 for 0000:00:10.0
PCI: Found 0000:00:10.1 [1106/3038] 000c03 00
PCI: Calling quirk c0277f60 for 0000:00:10.1
PCI: Calling quirk c0278510 for 0000:00:10.1
PCI: Calling quirk c03d6600 for 0000:00:10.1
PCI: Calling quirk c03d6a10 for 0000:00:10.1
PCI: Found 0000:00:10.2 [1106/3038] 000c03 00
PCI: Calling quirk c0277f60 for 0000:00:10.2
PCI: Calling quirk c0278510 for 0000:00:10.2
PCI: Calling quirk c03d6600 for 0000:00:10.2
PCI: Calling quirk c03d6a10 for 0000:00:10.2
PCI: Found 0000:00:10.3 [1106/3104] 000c03 00
PCI: Calling quirk c0277f60 for 0000:00:10.3
PCI: Calling quirk c0278510 for 0000:00:10.3
PCI: Calling quirk c03d6600 for 0000:00:10.3
PCI: Calling quirk c03d6a10 for 0000:00:10.3
PCI: Found 0000:00:11.0 [1106/3177] 000601 00
PCI: Calling quirk c0277a90 for 0000:00:11.0
PCI quirk: region 4000-407f claimed by vt8235 PM
PCI quirk: region 5000-500f claimed by vt8235 SMB
PCI: Calling quirk c0277f60 for 0000:00:11.0
PCI: Calling quirk c0278510 for 0000:00:11.0
PCI: Calling quirk c03d6600 for 0000:00:11.0
PCI: Calling quirk c03d6a10 for 0000:00:11.0
PCI: Found 0000:00:11.1 [1106/0571] 000101 00
PCI: Calling quirk c0277f60 for 0000:00:11.1
PCI: Calling quirk c0278510 for 0000:00:11.1
PCI: Calling quirk c03d6600 for 0000:00:11.1
PCI: Calling quirk c03d6a10 for 0000:00:11.1
PCI: Found 0000:00:11.5 [1106/3059] 000401 00
PCI: Calling quirk c0277f60 for 0000:00:11.5
PCI: Calling quirk c0278510 for 0000:00:11.5
PCI: Calling quirk c03d6600 for 0000:00:11.5
PCI: Calling quirk c03d6a10 for 0000:00:11.5
PCI: Found 0000:00:12.0 [1106/3065] 000200 00
PCI: Calling quirk c0277f60 for 0000:00:12.0
PCI: Calling quirk c0278510 for 0000:00:12.0
PCI: Calling quirk c03d6600 for 0000:00:12.0
PCI: Calling quirk c03d6a10 for 0000:00:12.0
PCI: Fixups for bus 0000:00
PCI: Scanning behind PCI bridge 0000:00:01.0, config 010100, pass 0
PCI: Scanning bus 0000:01
PCI: Found 0000:01:00.0 [1002/5157] 000300 00
PCI: Calling quirk c0277f60 for 0000:01:00.0
PCI: Calling quirk c0278510 for 0000:01:00.0
PCI: Calling quirk c03d6600 for 0000:01:00.0
PCI: Calling quirk c03d6a10 for 0000:01:00.0
Boot video device is 0000:01:00.0
PCI: Fixups for bus 0000:01
PCI: Bus scan for 0000:01 returning with max=01
PCI: Scanning behind PCI bridge 0000:00:01.0, config 010100, pass 1
PCI: Bus scan for 0000:00 returning with max=01
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled.
ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0, disabled.
ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0, disabled.
ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0200
pnp: ACPI device : hid PNP0B00
pnp: ACPI device : hid PNP0800
pnp: ACPI device : hid PNP0C04
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0303
pnp: ACPI device : hid PNPB02F
pnp: PnP ACPI: found 9 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn’t work, try “pci=routeirq”. If it helps, post a report
pnp: the driver ‘system’ has been registered
pnp: match found with the PnP device ’00:00′ and the driver ‘system’
got res [30000000:3000ffff] bus [30000000:3000ffff] flags 7200 for BAR 6 of 0000:00:0d.0
got res [30010000:30013fff] bus [30010000:30013fff] flags 7200 for BAR 6 of 0000:00:09.0
got res [ec000000:ec01ffff] bus [ec000000:ec01ffff] flags 7202 for BAR 6 of 0000:01:00.0
PCI: Bridge: 0000:00:01.0
IO window: 8000-8fff
MEM window: ec000000-edffffff
PREFETCH window: e0000000-e7ffffff
PCI: Calling quirk c0277ce0 for 0000:00:01.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
Machine check exception polling timer started.
SGI XFS with no debug enabled
Initializing Cryptographic API
PCI: Calling quirk c0277e30 for 0000:00:00.0
PCI: Calling quirk c0277e30 for 0000:00:01.0
PCI: Calling quirk c0277e30 for 0000:00:08.0
PCI: Calling quirk c0277e30 for 0000:00:08.1
PCI: Calling quirk c0277e30 for 0000:00:09.0
PCI: Calling quirk c0277e30 for 0000:00:0b.0
PCI: Calling quirk c0277e30 for 0000:00:0d.0
PCI: Calling quirk c0277e30 for 0000:00:10.0
PCI: Calling quirk c0277e30 for 0000:00:10.1
PCI: Calling quirk c0277e30 for 0000:00:10.2
PCI: Calling quirk c0277e30 for 0000:00:10.3
PCI: Calling quirk c0277e30 for 0000:00:11.0
PCI: Calling quirk c0277e30 for 0000:00:11.1
PCI: Calling quirk c0277e30 for 0000:00:11.5
PCI: Calling quirk c0277e30 for 0000:00:12.0
PCI: Calling quirk c0277e30 for 0000:01:00.0
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Fan [FAN] (on)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Thermal Zone [THRM] (22 C)
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA KT266/KY266x/KT333 chipset
agpgart: AGP aperture is 64M @ 0xe8000000
[drm] Initialized drm 1.0.0 20040925
pnp: the driver ‘i8042 kbd’ has been registered
pnp: match found with the PnP device ’00:07′ and the driver ‘i8042 kbd’
pnp: the driver ‘i8042 aux’ has been registered
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn’t have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 0) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 0) is a 16550A
pnp: the driver ‘serial’ has been registered
pnp: match found with the PnP device ’00:05′ and the driver ‘serial’
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
pnp: match found with the PnP device ’00:06′ and the driver ‘serial’
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
acpi_bus-0200 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt Link [ALKD] BIOS reported IRQ 0, using IRQ 23
ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [ALKD] -> GSI 23 (level, low) -> IRQ 16
PCI: Calling quirk c0277ce0 for 0000:00:12.0
PCI: Via IRQ fixup for 0000:00:12.0, from 10 to 0
eth0: VIA Rhine II at 0xef109000, 00:04:61:42:cd:74, IRQ 16.
eth0: MII PHY found at address 1, status 0x7869 advertising 05e1 Link 41e1.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PDC20268: IDE controller at PCI slot 0000:00:09.0
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 17
PDC20268: chipset revision 2
PDC20268: ROM enabled at 0x30010000
PDC20268: 100% native mode on irq 17
ide2: BM-DMA at 0xa000-0xa007, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xa008-0xa00f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2…
Probing IDE interface ide3…
hdg: WDC WD600BB-00CAA1, ATA DISK drive
ide3 at 0x9800-0x9807,0x9c02 on irq 17
VP_IDE: IDE controller at PCI slot 0000:00:11.1
acpi_bus-0200 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0, using IRQ 20
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 18
PCI: Calling quirk c0277ce0 for 0000:00:11.1
PCI: Via IRQ fixup for 0000:00:11.1, from 255 to 2
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xdc00-0xdc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0…
hda: WDC WD800BB-00CAA1, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1…
hdc: PLEXTOR CD-R PX-W2410A, ATAPI CD/DVD-ROM drive
hdd: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
pnp: the driver ‘ide’ has been registered
Probing IDE interface ide2…
Probing IDE interface ide4…
Probing IDE interface ide5…
hdg: max request size: 128KiB
hdg: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hdg: cache flushes not supported
hdg: hdg1 hdg2 hdg3
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes not supported
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 hda14 hda15 hda16 hda17 hda18 >
hdc: ATAPI 40X CD-ROM CD-R/RW drive, 4096kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
SCSI Media Changer driver v0.25
usbmon: debugfs is not available
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
acpi_bus-0200 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 0, using IRQ 21
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 19
PCI: Calling quirk c0277ce0 for 0000:00:10.3
PCI: Via IRQ fixup for 0000:00:10.3, from 11 to 3
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: reset hcs_params 0x3206 dbg=0 cc=3 pcc=2 ordered !ppc ports=6
ehci_hcd 0000:00:10.3: reset hcc_params 6872 thresh 7 uframes 256/512/1024
ehci_hcd 0000:00:10.3: capability 0001 at 68
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.3: irq 19, io mem 0xef108000
ehci_hcd 0000:00:10.3: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
PCI: Enabling Mem-Wr-Inval for device 0000:00:10.3
ehci_hcd 0000:00:10.3: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:10.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
ehci_hcd 0000:00:10.3: supports USB remote wakeup
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.14.1 ehci_hcd
usb usb1: SerialNumber: 0000:00:10.3
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface – got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: state 5 ports 6 chg 0000 evt 0000
ehci_hcd 0000:00:10.3: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
USB Universal Host Controller Interface driver v2.3
acpi_bus-0200 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 19
PCI: Calling quirk c0277ce0 for 0000:00:10.0
PCI: Via IRQ fixup for 0000:00:10.0, from 10 to 3
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: detected 2 ports
uhci_hcd 0000:00:10.0: check_and_reset_hc: legsup = 0x003a
uhci_hcd 0000:00:10.0: Performing full reset
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 19, io base 0x0000d000
uhci_hcd 0000:00:10.0: supports USB remote wakeup
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.14.1 uhci_hcd
usb usb2: SerialNumber: 0000:00:10.0
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface – got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
acpi_bus-0200 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 19
PCI: Calling quirk c0277ce0 for 0000:00:10.1
PCI: Via IRQ fixup for 0000:00:10.1, from 5 to 3
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: detected 2 ports
uhci_hcd 0000:00:10.1: check_and_reset_hc: legsup = 0x0010
uhci_hcd 0000:00:10.1: Performing full reset
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 19, io base 0x0000d400
uhci_hcd 0000:00:10.1: supports USB remote wakeup
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.14.1 uhci_hcd
usb usb3: SerialNumber: 0000:00:10.1
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface – got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
hub 1-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:10.3: port 4 full speed –> companion
ehci_hcd 0000:00:10.3: GetStatus port 4 status 003801 POWER OWNER sig=j CONNECT
hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.0: port 1 portsc 018a,00
hub 2-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
acpi_bus-0200 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 19
PCI: Calling quirk c0277ce0 for 0000:00:10.2
PCI: Via IRQ fixup for 0000:00:10.2, from 7 to 3
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: detected 2 ports
uhci_hcd 0000:00:10.2: check_and_reset_hc: legsup = 0x0010
uhci_hcd 0000:00:10.2: Performing full reset
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 19, io base 0x0000d800
uhci_hcd 0000:00:10.2: supports USB remote wakeup
usb usb4: default language 0x0409
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.14.1 uhci_hcd
usb usb4: SerialNumber: 0000:00:10.2
usb usb4: hotplug
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: hotplug
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface – got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
uhci_hcd 0000:00:10.0: port 2 portsc 008a,00
hub 2-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 3-0:1.0: state 5 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.1: port 1 portsc 008a,00
hub 3-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver…
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.1: port 2 portsc 009b,00
hub 3-0:1.0: port 2, status 0101, change 0003, 12 Mb/s
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
usb 3-2: new full speed USB device using uhci_hcd and address 2
usb 3-2: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 3-2: hotplug
usb 3-2: adding 3-2:1.0 (config #1, interface 0)
usb 3-2:1.0: hotplug
hub 3-2:1.0: usb_probe_interface
hub 3-2:1.0: usb_probe_interface – got id
hub 3-2:1.0: USB hub found
hub 3-2:1.0: 4 ports detected
hub 3-2:1.0: standalone hub
hub 3-2:1.0: individual port power switching
hub 3-2:1.0: individual port over-current protection
hub 3-2:1.0: power on to power good time: 500ms
hub 3-2:1.0: local power source is good
hub 3-2:1.0: enabling power on all ports
uhci_hcd 0000:00:10.0: suspend_rh (auto-stop)
hub 4-0:1.0: state 5 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.2: port 1 portsc 008a,00
hub 4-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
hub 4-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.2: port 2 portsc 018a,00
hub 4-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
hub 3-0:1.0: state 5 ports 2 chg 0000 evt 0004
hub 3-2:1.0: state 5 ports 4 chg 0000 evt 0010
usbcore: registered new driver hiddev
hub 3-2:1.0: port 4, status 0301, change 0001, 1.5 Mb/s
hub 3-2:1.0: debounce: port 4: total 100ms stable 100ms status 0x301
usb 3-2.4: new low speed USB device using uhci_hcd and address 3
usb 3-2.4: skipped 1 descriptor after interface
usb 3-2.4: default language 0x0409
usb 3-2.4: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-2.4: Product: N48
usb 3-2.4: Manufacturer: Logitech
usb 3-2.4: hotplug
usb 3-2.4: adding 3-2.4:1.0 (config #1, interface 0)
usb 3-2.4:1.0: hotplug
hub 4-0:1.0: state 5 ports 2 chg 0000 evt 0000
usbhid 3-2.4:1.0: usb_probe_interface
usbhid 3-2.4:1.0: usb_probe_interface – got id
input: USB HID v1.00 Mouse [Logitech N48] on usb-0000:00:10.1-2.4
hub 3-2:1.0: state 5 ports 4 chg 0000 evt 0010
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
i2c-parport: using default base 0x378
i2c-pca-isa: i/o base 0x000330. irq 10
i2c-sis96x version 1.0.0
input: AT Translated Set 2 keyboard on isa0060/serio0
uhci_hcd 0000:00:10.2: suspend_rh (auto-stop)
pc87360: PC8736x not detected, module not inserted.
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
NET: Registered protocol family 2
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 5, 131072 bytes)
TCP bind hash table entries: 32768 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices:
SLPB PCI0 USB0 USB1 USB2 USB6 USB7 USB8 USB9 LAN0 UAR1
ACPI: (supports S0 S1 S3 S4 S5)
ReiserFS: hda3: found reiserfs format “3.6” with standard journal
(REISERFSK-Plattencheck….)
ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using IRQ 22
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 20
PCI: Calling quirk c0277ce0 for 0000:00:11.5
PCI: Via IRQ fixup for 0000:00:11.5, from 7 to 4
PCI: Enabling bus mastering for device 0000:00:11.5
PCI: Setting latency timer of device 0000:00:11.5 to 64
Linux video capture interface: v1.00
bttv: driver version 0.9.16 loaded
bttv: using 16 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 16 (level, low) -> IRQ 21
bttv0: Bt878 (rev 17) at 0000:00:08.0, irq: 21, latency: 16, mmio: 0xef105000
bttv0: detected: AVermedia AverTV DVB-T 771 [card=123], PCI subsystem ID is 1461:0771
bttv0: using: AVerMedia AVerTV DVB-T 771 [card=123,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffff9f [init]
bttv0: using tuner=4
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .. ok
bttv0: add subdevice “remote0”
bttv0: add subdevice “dvb0”
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:00:08.1[A] -> GSI 16 (level, low) -> IRQ 21
bt878(0): Bt878 (rev 17) at 00:08.1, irq: 21, latency: 16, memory: 0xef104000
DVB: registering new adapter (bttv0).
DVB: registering frontend 0 (Zarlink MT352 DVB-T)…
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.3 (4095 buckets, 32760 max) – 216 bytes per conntrack
eth0: Promiscuous mode enabled.
device eth0 entered promiscuous mode
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 21
[drm] Initialized radeon 1.17.0 20050311 on minor 0:
mtrr: 0xe0000000,0x8000000 overlaps existing 0xe0000000,0x4000000
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode

(wenn Dir da irgendetwas sonstiges Verbesserungswürdiges :O) auffällt, Ingo: Ich bin dankbarer Abnehmer jedweder Form von Infos diesbezüglich!)

h.) cat proc/interrupts ergibt:
CPU0
0: 1771842 IO-APIC-edge timer
1: 9328 IO-APIC-edge i8042
8: 1 IO-APIC-edge rtc
9: 0 IO-APIC-level acpi
10: 0 IO-APIC-edge i2c-pca-isa
14: 105700 IO-APIC-edge ide0
15: 83 IO-APIC-edge ide1
16: 8064 IO-APIC-level eth0
17: 25828 IO-APIC-level ide3
19: 81403 IO-APIC-level ehci_hcd:usb1, uhci_hcd:usb2, uhci_hcd:usb3, uhci_hcd:usb4
20: 7714 IO-APIC-level VIA8233
21: 659937 IO-APIC-level bttv0, bt878, radeon@pci:0000:01:00.0
NMI: 0
LOC: 1771668
ERR: 0
MIS: 0

i.) zcat /proc/config.z | grep USB | egrep -v ‘^#’ liefert:
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB=y
CONFIG_USB_DEBUG=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=y
CONFIG_USB_PRINTER=y
CONFIG_USB_STORAGE=y
CONFIG_USB_HID=y
CONFIG_USB_HIDINPUT=y
CONFIG_USB_HIDDEV=y
CONFIG_USB_MON=y

Sollte ich noch etwas vergessen haben, bitte eben kurz mailen! DANKE !

Schönes Wochenende !
Gruss,
Meino